AI summary · arXiv: 2611.10867v1 · eess.SP

Missed Interferers in Ray-Traced Radio Maps: A Digital-Twin and Stochastic Geometry Study of Aerial Coverage

Saad Masrur, Ismail Guvenc
Original paper Submitted to arXiv on 07 Nov. 2026 Under Review License: NONEXCLUSIVE-DISTRIB 1.0 Also in: fr

How to read this summary? Illustrated guide

The essentials

The study shows that undersampled ray-traced aerial radio maps miss distant LOS interferers, biasing SINR coverage, while a deterministic engine and an unfitted stochastic-geometry model provide more reliable analysis.

Question

How do ray count, cell size, and modeled network extent affect UAV SINR coverage predicted by ray-traced digital twins? The authors also examine how altitude, association, load, and operator selection affect aerial coverage.

Method

The authors built a Sionna RT digital twin covering 8.64 × 9.50 km around Raleigh, with 18,591 buildings and two operator networks comprising 11 and 9 sites, and evaluated ten UAV altitudes from 40 to 300 m. They compared Monte Carlo radio maps using 10^6–10^8 rays per sector and 5–20 m cells against a LOS-aware deterministic engine validated with Sionna’s path solver, then developed an unfitted stochastic-geometry model and compared coverage across thresholds, radii, association rules, loads, and operators.

Findings

  • Result At 50 m, the 10^7-ray, 5 m-cell radio map underestimated coverage at −2 dB by 15.8 percentage points relative to the deterministic engine.
  • Result At 100 m, the same radio-map configuration overestimated coverage at +2 dB by 26.2 percentage points because it missed distant interferers.
  • Result The stochastic-geometry model reproduced deterministic-engine coverage with a 3.9% RMSE for Operator A across the evaluated altitudes and thresholds, without fitting.
  • Authors’ interpretation Under the modeled LOS conditions, mean interference increases logarithmically with network radius, so omitting distant sites can materially overestimate coverage.
    See the passage in the paper
    Hence, far sites cannot be ignored, unlike for path-loss exponents above two.
  • Result Selecting the better operator raised the minimum SINR along the best corridor by 1.0–3.9 dB up to 100 m compared with the better single operator.

Limitations

  • The digital twin assumes simplified environmental and network conditions, and the authors state that its absolute coverage results need field validation.
    See the passage in the paper
    As the ACDT assumes flat terrain, no foliage, full Fresnel clearance, full buffers, and assumed azimuths and tilts, its absolute numbers require field validation, such as at the NSF AERPAW platform, which is left for future work.
  • The stochastic-geometry model idealizes the network as a homogeneous PPP with LOS propagation and does not model buildings or ground reflection.
  • The reported dual-operator corridor improvement is an upper bound because operator changes are assumed to have no cost.
    See the passage in the paper
    This gain is an upper bound, because the UAV changes operator at no cost.

Why it matters

The authors argue that aerial digital twins must check radio-map convergence and report or bound the modeled network radius, because feasible ray budgets can miss important interferers. Their deterministic engine and unfitted stochastic-geometry model provide complementary ways to assess coverage, while the results highlight the potential effects of association, load, and operator diversity.

Written by AI from the paper. Passages are checked word for word against the text we analysed; the rest may contain errors.

AI-generated keywords: UAV communications SINR coverage ray tracing digital twins interference modeling

Read further

  • Comprehensive Summary
  • Layman's Summary
  • Blog article
  • Original abstract
The paper investigates whether ray-traced digital twins can reliably predict cellular signal-to-interference-plus-noise ratio (SINR) coverage for UAVs flying over a city, and how much of the surrounding network must be included in the model. The authors build a Sionna RT digital twin covering an 8.64 × 9.50 km area of Raleigh, North Carolina. The model includes 18,591 buildings and two overlapping 600 MHz operator networks. Each network has 20 sites, each with three sectors and antennas mounted at 30 m with a 6-degree downtilt. Coverage is evaluated on a 5 m grid at ten UAV altitudes from 40 to 300 m, using the fraction of cells exceeding specified SINR thresholds. The first finding concerns Sionna RT’s Monte Carlo radio-map solver, whose estimates depend on how many launched rays cross each map cell. The authors approximate the probability that a cell receives no direct or ground-reflected ray. On an aerial plane, the expected number of ray hits decreases rapidly with distance, approximately in proportion to the cube of the distance. For a 6 km range, 5 m cells, and a 20 m height difference between the transmitter and UAV, their analysis estimates that roughly 16 billion rays per sector would be needed to give a distant cell a 95% chance of receiving a ray—far more than the tested budgets. With 10 million rays per sector and 5 m cells, 40% of cells at 50 m altitude and 24% at 100 m receive no ray from any sector. Treating these empty cells as outages depresses estimated coverage at low SINR thresholds. For Operator A at 50 m, coverage at −2 dB is 59.1% in the radio map, compared with 74.9% in the deterministic calculation. However, cells that do receive rays often miss distant interferers, causing their estimated SINR to be too high. At 100 m and +2 dB, radio-map coverage is 63.7%, compared with 37.5% in the deterministic result. Thus, the errors can distort both coverage estimates and the apparent effect of altitude. Increasing the ray budget or cell size reduces the number of empty cells more quickly than it resolves missed distant interference. At 100 m, even 100 million rays leave 81% of sector–cell pairs beyond 3 km without a ray. For comparison, the authors develop DT-det, a deterministic engine that checks direct-path visibility for every site and grid cell, includes specular ground reflection, and applies knife-edge loss to a small number of obstructed paths. Validation against Sionna’s path solver on sampled cells shows agreement in line-of-sight decisions, a median SINR error below 0.2 dB, and coverage differences of no more than 5%. The authors also construct a stochastic-geometry model with randomly located sites, realistic three-sector antenna patterns, strongest-sector association, and interference from the serving site’s other sectors. Without fitted parameters, this model matches DT-det with coverage root mean square errors of 3.9% for Operator A and 3.2% for Operator B across the tested altitudes and thresholds. The analysis predicts that interference from line-of-sight sites increases logarithmically with the modeled network radius. At 100 m, excluding interferers beyond 4 km overestimates 0 dB coverage by 31%; extending the radius to 8 km reduces the discrepancy to about 2%. The authors therefore recommend that digital twins report their modeled extent and account for sites outside it. Altitude has a modest effect at low thresholds and a stronger effect at high thresholds.

Was this synthesis useful?

Score: 0

Why do we need votes?

Votes are used to determine whether we need to re-run our summarizing tools. If the count reaches -10, our tools can be restarted.

Figures and plots

Ask about a figure by number or use its question button to request visual analysis. Up to two figures and four image panels per question. Values read from plots are approximate; check the original data.

AI assistant instructions?

Tools for this paper

Explain it differently 1 free rewrite left today
Save to a collection Group papers in collections to compare them, chat with them and export them. Continue with Google Create a free account Log in

Advanced tools Premium

For researchers who follow a field closely: citation alerts, journal-club slides, version comparison and Zotero export. Discover Premium

Zotero Zotero guide
Citation alerts Citation alerts guide
Who works on it?

Among the 23 papers around this one, the name that comes back most: S. Maeng (3 papers)

3 more people sign several of them. The full map adds their institutions and approaches, from the papers of the last years.

Continue with Google Create a free account: your first map is free
Weekly letter Presented in "Computing beyond AI this week" of 16 November 2026. Computing beyond AI this week: The costs hidden in our maps, networks and algorithms · Receive one by email for free
A rising topic This paper is part of "Simulated cities for better wireless connections", rising in Signal Processing (eess.SP) (×9.2 compared with usual). The rising topics of that week · The history of the term

Papers around this one

See them on a map

Ranked by how close their title and abstract are to this paper’s. Select some to read them together.

Closest papers

  1. Close Shared data, tool or method
    Validation of Sionna Ray-Tracer for Urban Signal-Strength Prediction Using Large-Scale Drive-Test Measurements
    Kamil Chmela, P. Svoboda, W. Wiedner et al. · 2026 · International Symposium ELMAR · Not summarized yet

    The study validates Sionna ray-tracing signal-strength predictions against large-scale outdoor measurements, while this paper uses Sionna RT to build aerial coverage maps.

    Abstract

    Accurate channel modelling is a key prerequisite for planning and improvement of wireless communication networks. Obtaining a precise channel model is therefore a pivotal task for telecommunication engineers. One method that has gained in popularity in recent years is ray-tracing. Given the widespread use, it is important to understand the strengths and weaknesses of ray-tracing and to know what performance is to be expected in praxis. In this paper, we compare a large dataset of outdoor measurements of signal strength with simulations and assess the obtained error changes given different antenna models, 3D models with different levels of detail and various simulation settings. The benefits …

  2. Close Same question Cited by this paper
    Beyond RSRP Coverage: UAV Serviceability in Interference-Limited Urban 5G NR Networks
    M. Hossen, V. K. Shah, I. Guvenç · 2026 · arXiv.org · preprint, not peer reviewed · cited 1 time · Not summarized yet

    The study evaluates UAV serviceability under urban inter-cell interference, while this paper examines how modeled interference affects UAV SINR coverage.

    Abstract

    Reference signal received power (RSRP) is commonly used to assess 5G cellular coverage, but it may substantially overestimate the connectivity available to cellular-connected unmanned aerial vehicles (UAVs) under strong inter-cell interference (ICI). As a UAV ascends, reduced blockage can strengthen the serving signal, while increased line-of-sight visibility to neighboring sectors can intensify ICI. This paper develops a trajectory-aware, 3GPP-based system-level framework for evaluating UAV radio serviceability during a three-dimensional flight in an urban 5G New Radio network. The framework jointly evaluates RSRP, reference signal received quality (RSRQ), and signal-to-interference-plus-no…

  3. Close Broader context
    RadioTraj3D: Height-Aware Adaptive Sampling for 3D Radio-Map Reconstruction from Ultra-Sparse Trajectories
    Zi-Xuan Guo, Xiu-Cheng Wang, Wen-Shuo Chen et al. · 2026 · Not summarized yet

    RadioTraj3D reconstructs three-dimensional radio maps from sparse aerial measurements, whereas this paper studies SINR coverage in ray-traced maps.

    Abstract

    Aerial networks require radio propagation information at unvisited positions and heights to plan routes, select links, and allocate wireless resources. A three-dimensional radio map (3D RM) represents propagation conditions over the service area, enabling these decisions before flight. However, constructing such a map from autonomous aerial vehicle (AAV) measurements is challenging, since radio measurements are available only along the trajectory, whereas the target covers the 3D service volume. Existing methods use fixed AAV trajectories that ignore how building distributions and heights affect electromagnetic propagation, missing the heights most informative for RM reconstruction. To addre…

  4. Close Same method, another problem
    A Ray-Traced Digital Twin for 5G NR Positioning with OpenAirInterface
    Nima Chaharbaghi, F. Kaltenberger, Bartosz Podrygajlo et al. · 2026 · Not summarized yet

    The study uses a Sionna-RT digital twin to evaluate 5G positioning, while this paper uses one to evaluate aerial SINR coverage.

    Abstract

    Evaluating 5G positioning on a physical testbed ties every measurement to one propagation environment and one antenna layout, so any question about an alternative deployment requires a new field campaign. We present a ray-traced digital twin of the GEO-5G testbed at EURECOM that drives an unmodified OpenAirInterface (OAI) 5G stack with per-antenna channels computed by Sionna-RT over a 3D model of the site. The distributed gNB antennas are modelled as independent radio devices rather than as elements of a compact array, which preserves the per-antenna absolute delays on which time-difference-of-arrival (TDoA) positioning depends. With them preserved, the twin drives OAI's SRS-based UL-TDoA pi…

  5. Close Same question Cited by this paper
    Analysis and Prediction of Coverage and Channel Rank for UAV Networks in Rural Scenarios With Foliage
    Donggu Lee, O. Ozdemir, Ram Asokan et al. · 2025 · IEEE Open Journal of Vehicular Technology · cited 9 times · Not summarized yet

    The study uses ray tracing to assess UAV RF coverage in rural foliage, while this paper evaluates UAV coverage in an urban cellular network.

    Abstract

    Uncrewed aerial vehicles (UAVs) are expected to play a key role in 6G-enabled vehicular-to-everything (V2X) communications, requiring high data rates, low latency, and reliable connectivity for mission-critical applications. Multi-input multi-output (MIMO) technology is essential for meeting these demands. However, UAV link performance is significantly affected by environmental factors such as signal attenuation, multipath propagation, and blockage from obstacles, particularly dense foliage in rural areas. In this paper, we investigate RF coverage and channel rank over UAV channels in foliage-dominated rural environments using ray tracing (RT) simulations. We conduct RT-based channel rank an…

  6. Close Groundwork for this paper Cited by this paper
    Sionna RT: Differentiable Ray Tracing for Radio Propagation Modeling
    J. Hoydis, Fayçal Aït Aoudia, Sebastian Cammerer et al. · 2023 · 2023 IEEE Globecom Workshops (GC Wkshps) · cited 427 times · Not summarized yet

    Sionna RT describes the differentiable ray tracer used by this paper to construct its radio propagation digital twin.

    Abstract

    Sionna™ is a GPU-accelerated open-source library for link-level simulations based on TensorFlow. Since release v0.14 it integrates a differentiable ray tracer (RT) for the simulation of radio wave propagation. This unique feature allows for the computation of gradients of the channel impulse response and other related quantities with respect to many system and environment parameters, such as material properties, antenna patterns, array geometries, as well as transmitter and receiver orientations and positions. In this paper, we outline the key components of Sionna RT and showcase example applications such as learning radio materials and optimizing transmitter orientations by gradient descent…

  7. Close Same method, another problem
    ARCTAN: Arbitrary RF Containment Using Tactical Aerial Networks and Differentiable Ray Tracing
    Samuel Rivera, Zhi-Hui Gao, Yi-Ming Li et al. · 2026 · Not summarized yet

    ARCTAN uses differentiable ray tracing to optimize aerial RF containment, while this paper uses ray tracing to assess aerial cellular coverage.

    Abstract

    Aerial base stations (ABSs) can rapidly establish connectivity in ad hoc, infrastructure-deprived environments, but their broadcast, line-of-sight transmissions leak far beyond the intended service area, exposing communications to passive eavesdropping and interference. Prior physical layer defenses based on cooperative jamming typically assume known eavesdropper locations, simplified statistical channels, or continuously repositioned jammers. We instead pose the problem as a radio frequency (RF) containment: confining usable signal to a user-defined, arbitrarily-shaped target zone while denying it elsewhere independent of eavesdropper location. We present ARCTAN, a gradient-based optimizati…

  8. Close Same question
    AI-Enabled Wireless Propagation Modeling and Radio Environment Maps for 5G Aerial Wireless Networks
    G. Reddy, Kürşat Tekbıyık, Bryton J. Petersen et al. · 2026 · IEEE Journal of Selected Topics in Electromagnetics, Antennas and Propagation · Not summarized yet

    The study models radio environments for aerial networks facing LoS interference, while this paper analyzes UAV SINR coverage affected by LoS interferers.

    Abstract

    With the gaining prominence of aerial mobility applications, their success depends on the seamless integration of terrestrial and non-terrestrial network connectivity. However, providing reliable connectivity from terrestrial telecommunication networks remains challenging due to multi-cell interference from base stations (BSs) under line-of-sight (LoS) conditions to unmanned aerial vehicles (UAVs), coverage holes caused by antenna sidelobe degradation, localized multipath fading effects, and the high-speed dynamics of aerial users. To model such complexities, often exacerbated by sparse real-world data, this work proposes a dual-stage radio environment map (REM) framework. Our approach physi…

Prior work it builds on

  1. Related Groundwork for this paper
    Modeling Heterogeneous Network Interference Using Poisson Point Processes
    Robert W. Heath, Marios Kountouris, Tian-Yang Bai · 2012 · IEEE Transactions on Signal Processing · cited 167 times · Not summarized yet

    The study uses stochastic geometry to model heterogeneous cellular interference, an analytical approach this paper also applies to aerial coverage.

    Abstract

    Cellular systems are becoming more heterogeneous with the introduction of low power nodes including femtocells, relays, and distributed antennas. Unfortunately, the resulting interference environment is also becoming more complicated, making evaluation of different communication strategies challenging in both analysis and simulation. Leveraging recent applications of stochastic geometry to analyze cellular systems, this paper proposes to analyze downlink performance in a fixed-size cell, which is inscribed within a weighted Voronoi cell in a Poisson field of interferers. A nearest out-of-cell interferer, out-of-cell interferers outside a guard region, and cross-tier interferers are included …

  2. Related Same question Used in depth by this paper
    Drone delivery: Reliable Cellular UAV Communication Using Multi-Operator Diversity
    A. Colpaert, Michaël Raes, E. Vinogradov et al. · 2021 · ICC 2022 - IEEE International Conference on Communications · cited 18 times · Not summarized yet

    The study examines multi-operator diversity for reliable cellular UAV communication, and this paper evaluates how choosing between two operators affects aerial coverage.

    Abstract

    The market size of Unmanned Aerial Vehicles (UAVs, a.k.a drones) can reach up to 10% of the global market value. In particular, drone delivery is one of the most attractive applications. The growing number of drones requires appropriate traffic management systems that will rely on cellular networks. However, it has been shown in the literature that these networks cannot provide reliable communication due to low coverage probability and frequent handovers. This article presents a potential solution targeting these problems while requiring no modifications of the existing infrastructure. Namely, equipping the UAV with multiple cellular modems to connect to different providers’ networks introdu…

  3. Related* Groundwork for this paper
    An advanced 3D ray launching method for wireless propagation prediction
    G. Durgin, N. Patwari, T. Rappaport · 1997 · 1997 IEEE 47th Vehicular Technology Conference. Technology in Motion · cited 115 times · Not summarized yet

    The cited ray-launching method concerns wireless propagation prediction, a propagation-modeling foundation relevant to this paper's ray-traced coverage analysis.

  4. Related Same question
    Base Station Antenna Uptilt Optimization for Cellular-Connected Drone Corridors
    S. Maeng, Md Moin Uddin Chowdhury, Í. Güvenç et al. · 2021 · IEEE Transactions on Aerospace and Electronic Systems · cited 26 times · Not summarized yet

    The study optimizes antenna uptilt to improve cellular coverage in drone corridors, while this paper examines UAV coverage across altitudes and network choices.

    Abstract

    Reliable wireless coverage in drone corridors is critical to enable a connected, safe, and secure airspace. To support beyond-visual-line-of-sight operations of aerial vehicles in a drone corridor, cellular base stations (BSs) can serve as a convenient infrastructure as they are widely deployed to provide seamless wireless coverage. However, antennas in the existing cellular networks are downtilted to optimally serve their ground users, which results in coverage holes at higher altitudes when they are used to serve drones. In this article, we consider the use of additional uptilted antennas at each cellular BS and optimize the uptilt angle to maximize the wireless coverage probability across…

  5. Related Shared data, tool or method
    Modeling and Analysis of Air-to-Ground Cellular KPIs in a 5G Testbed Using Android Smartphones
    Simran Singh, Anıl Gürses, O. Ozdemir et al. · 2026 · IEEE Aerospace Conference · cited 1 time · Not summarized yet

    The study measures air-to-ground cellular KPIs in a 5G testbed, providing flight-based observations relevant to this paper's modeled aerial link performance.

    Abstract

    The integration of cellular communication with Unmanned Aerial Vehicles (UAVs) extends the range of command and control (C2) and payload communications of autonomous UAV applications. Accurate modeling of this air-to-ground wireless environment aids UAV mission planning. Models built on and insights obtained from real-life experiments intricately capture the variations in air-to-ground link quality with UAV position, offering more fidelity for simulations and system design than those that rely on generic theoretical models designed for ground scenarios or ray-tracing simulations. In this work, we conduct multiple aerial flights at the Aerial Experimentation and Research Platform for Advanced…

How are these papers found?

We compare the title and abstract of this paper with those of every paper summarized on this site, and with the papers Semantic Scholar recommends, those it cites and those citing it (for a much-cited paper, its most recent citations and, from OpenAlex, the most cited ones). Among the prior work and the follow-ups, the papers that use each other in depth, a method it uses and the much-cited follow-ups come a little higher. The levels (very close, close, related) come from the similarity of the texts, not from a judgment of quality; * marks a paper without an abstract, compared by its title. The sentence under a paper is written by an AI from the two abstracts: check it in the papers. A paper marked not relevant by three readers leaves the list.

Updated on 16 November 2026.

The illustrated guide to the papers around a paper

Disclaimer: The AI-based summarization tool and virtual assistant provided on this website may not always provide accurate and complete summaries or responses. We encourage you to carefully review and evaluate the generated content to ensure its quality and relevance to your needs.